9e11cb8dbb06526c9ea51f9911fe2fa

S2000水性环氧内面漆

S2000水性环氧内面漆

S2000 WATERBORNE EPOXY INTERIOR TOP COATING

产品简介

Description

 

 

水性环氧内面漆是采用环氧树脂、水性胺固化剂、高级防腐蚀颜填料配制的双组分环保涂料。作为集装箱涂装的内面漆使用,具有硬度高、耐磨耐化学品等特性。

Waterborne epoxy interior finish is a two-component environment-friendly coating made of epoxy resin, waterborne amine curing agent and advanced anticorrosive pigments and fillers. As an interior finish for container painting, it has the characteristics of high hardness, abrasion resistance and chemical resistance.

推荐用途

Recommended use

推荐用作集装箱内面漆

As the interior top coating on the containers surface.

物理参数

PHYSICAL CONSTANTS:

颜色

Colour:

灰色/铁红

Gray/Red oxide

光泽

Gloss:

平光

Low gloss

体积固含

Volume solids, %:

42.0±2.0

理论涂布率

Theoretical spreading rate:

10.5平米/.40微米

10.5m²/litre – 40micron

比重

Specific gravity:

1.4公斤/

About 1.4kg/L

表干时间

Surface dry:

30分钟/25

30 minutes at 25 

硬干时间

Dry hard:

6小时/25

6 (approx.) hours at 25

完全固化

Dry through:

7-14

7-14 days at 25F(depends on the temperature and air humidity)

施工参数

APPLICATION DETAILS:

配比

Mixing ratio:

主剂:固化剂=91(重量比)

S1000:S1000G=9:1(BY WEIGHT)

 

 

施工方法

Application method:

无气喷涂

Airless spray

空气喷涂

Air spray

刷涂

Brush

稀释比例

Thinning ratio:

0-10%

5-20%

5-10%

稀释剂

Thinner:

自来水

Tape water

混合适用期

Pot life:

8h

 

推荐膜厚

Recommend thichness

40微米/道(干膜);100微米/道(湿膜)

40μm/coat(dry film);100μm/coat(wet film)

施工指南

APPLICATION DETAILS

施工条件

 

Application conditions:

只适用于通风良好的区域,并确保在密闭空间或空气停滞时应用足够的强制通风。流水线作业必须采用强制通风干燥(50-80)以保证施工的顺畅性。

Apply only in well ventilated areas and ensure that adequate forced ventilation exists when applying paint in confined spaces or when the air is stagnant. In confined spaces provide adequate ventilation during application and drying.

底材处理

 

SUBSTRATE  PREPARATION:

 

待涂装钢铁除去底材表面上的油,灰和其它杂物,喷砂处理至Sa2.5,粗糙度达到20-40微米。

To remove oil, ash and other debris on the surface of the base. Sandblasting is processed to Sa2.5 with surface roughness of 20-40 microns.

New steel: Abrasive blasting to minimum Sa2.5 is recommended. The surface

施工方法

 

 

Application methods

小面积施工可采用刷涂、辊涂或者空气喷涂,稀释比率  体积比0-20%

无气喷涂:喷嘴口径:0.017~0.021" 喷嘴压力:15~20MP

稀释比率:5%(体积比),以上数据也可根据现场情况进行调整。

Brush, Roller, Air spray, Only for small area, Thinning ratio 5-20% (by volume).

must be completely clean and dry, its temperature must be above the dew point to avoid condensation.

安全事项

 

 

 

Safety:

 

小心轻放。在使用前和使用期间,观察包装和油漆容器上的所有安全标签,遵守当地或国家的所有安全规定。对于个人保护,包括但不限于保护肺部、眼睛和皮肤,严禁吞咽油漆,或在与油漆直接接触的情况下进行医疗治疗。采取必要的预防措施,防止可能发生火灾或爆炸的危险,以及保护环境。

Handle with care. Before and during use, observe all safety labels on packaging and paint containers, follow all local or national safety regulations. This goes for personal protection such as, but not limited to, protection of lungs, eyes and of the skin, medical treatment in case of swallowing the paint or in case of other direct contact with the paint. Take necessary precautions against possible risks of fire or explosions as well as protection of the environment.

 

储存条件

Storage condition:

5-35通风干燥处保存。

Should be stored under the conditions of 5-35.

储存期限

Storage life

主剂:12个月;固化剂:12个月。

Base: 12monthsCuring agent: 12months

    

 

 

OTHER NOTES

 

本产品仅限于专业人员使用,本说明书提供的数据均为试验获得, 但通常产品的使用都是在我们的控制范围之外,所以我们只对产品的质量担保,我们保留预先修改说明书的权利。

The product for professional used only, and the information of this data sheet is based on laboratory testing, since conditions of use beyond our control, so this

information is without warranty but the quality of the product itself. We reserve

the right to change the data without notice.

发布日期

Issue date:

2017.12

首页    水性 集装箱漆    S2000水性环氧内面漆